stm32的问题，.什么我这个USART通信程序发不出数据??

引用第1楼nhlijiaming于2010-08-06 21:56发表的 :
STM32找猴子吧....
stm32据说稳定性不如avr, avr的价格啊........
我在2440和cortex-m0两个考虑中....

AVR稳定性其实不如STM32，因为虽然AVR运行比STM32稳定，但是STM32的保护措施更多。比如我的ECG处理上就应用了时钟安全系统（CSS），如果晶振挂掉，系统切换到内部时钟，并且放出故障信号。STM32看门狗也是很强悍地说。NMI，定时器刹车和ADC看门狗更是利器。

2440和M0完全不同的档次，现在大家都用6410有条件搞个吧，性能好，用得爽。不过开发起来其实一样的。
M0号称代替51，因为硅片面积比51小。
STM8可以干掉AVR，STM8使用更方便。而且据说AVR以后要登记供货，比较麻烦，散货可能难以拿到。

LZ把整个工程打包吧，估计是哪里配置错了

请问楼主，我没有出现你写代码的错误，但是结果和你的一样，是怎么回事啊？急！！！！！！！！！！！！望尽快给答复，谢谢！

附我的代码：
#include "stm32f10x.h"

/* Private variables ---------------------------------------------------------*/
GPIO_InitTypeDef GPIO_InitStructure;

/* Private function prototypes -----------------------------------------------*/
void delay(uint32_t nCount);
void UART1_GPIO_Configuration(void);
void UART1_Configuration(void);

/**********************************主函数****************************************/
int main(void)
{
  /* Setup STM32 system (clock, PLL and Flash configuration) */
  SystemInit();

  /* GPIOx and AFIO clock enable */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOB|RCC_APB2Periph_AFIO, ENABLE);
   /* USART1 clock enable */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);

  UART1_GPIO_Configuration();
  UART1_Configuration();

  while(1)
  {
        GPIO_SetBits(GPIOB, GPIO_Pin_5);
        USART_SendData(USART1, (u8) 0xa4);
        while(USART_GetFlagStatus(USART1, USART_FLAG_TC) == RESET);
        delay(0xffff);
        GPIO_ResetBits(GPIOB, GPIO_Pin_5);
        delay(0xfffff);
  }

}

/*********************************配置UART的GPIO口*************************************/
void UART1_GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// Configure USART1_Tx as alternate function push-pull
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);

// Configure USART1_Rx as input floating
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);

// Configure GPIOB
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);

}

/************************************配置串口参数***********************************/

void UART1_Configuration(void)
{

   USART_InitTypeDef USART_InitStructure;
   USART_ClockInitTypeDef USART_ClockInitStructure;

   USART_InitStructure.USART_BaudRate = 115200;
   USART_InitStructure.USART_WordLength = USART_WordLength_8b;
   USART_InitStructure.USART_StopBits = USART_StopBits_1;
   USART_InitStructure.USART_Parity = USART_Parity_No ;
   USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
   USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;

   USART_ClockInitStructure.USART_Clock = USART_Clock_Disable;
   USART_ClockInitStructure.USART_CPOL = USART_CPOL_Low;
   USART_ClockInitStructure.USART_CPHA = USART_CPHA_2Edge;
   USART_ClockInitStructure.USART_LastBit = USART_LastBit_Disable;

   USART_ClockInit(USART1,&USART_ClockInitStructure);

   USART_Init(USART1, &USART_InitStructure);

   USART_Cmd(USART1, ENABLE);
}

/***********************************延时子函数***********************************/

void delay(uint32_t nCount)
{
  for(; nCount != 0; nCount--);
}
/********************************End of function def********************************/

#ifdef  USE_FULL_ASSERT

/**
  * @brief  Reports the name of the source file and the source line number
  *   where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t* file, uint32_t line)
{
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\\r\\n", file, line) */

  /* Infinite loop */
  while (1)
  {
  }
}
#endif

/**
  * @}
  */